<p>Important note emergency callsThe e3300 is not designed for making emergency calls when the mains power fails. So you should make alternative arrangements for access to Emergency Services. (This means that you should also have a basic phone that does not need mains power, connected to your line so that you can make calls during a power failure.)</p><p>If you need help The Binatone Help Line is available from 9.00 am to 5.00 pm, Monday to Friday, on 01325 304 473</p><p>Unpacking your e3300In the box are:I I I I I I</p><p>the cordless handset (up to six, depending on which e3300 system you have bought) the base unit rechargeable batteries and a battery compartment cover for each handset a telephone line cable for the base unit a mains power lead and adapter for the base unit up to five charger pods, each with a separate mains power lead and adapter.</p><p>Keep the packaging materials in a safe place in case you later need to transport the unit. Keep your sales (till) receipt, which is your guarantee.</p><p>Where to find itEARPIECE Dont hold this too close to your ear while the handset is ringing the ringing gets louder as it continues. HANG UP / C (Cancel) button Press to hang up at the end of a call. Press for 1 second to lock the keypad; or for 3 seconds to turn the handset on and off. While dialling or programming, press briefly to delete digits from the display; or press and hold to clear the display. PROG button Press to start programming. Press during a call to make a note of a number in the Notebook. UP L and DOWN M buttons Press during a call to adjust the volume in the earpiece. Press to move through the list of stored numbers or Caller Display records. PHONE /OK button Press to begin or answer a telephone call. Press while programming to confirm your selection. R (Recall) button You may need this during a call if your e3300 is connected to a PBX, or if you use BTs Select Services. MEMORY button Press to store numbers in memory and to make calls to stored numbers. IN USE light This comes on when you have a connection to the telephone line. HANDSET LOCATOR button Press to make all registered handsets ring, (useful if you've forgotten where you put a handset). SCROLL ( #) buttons When a long number (more than 16 digits) is shown on the display, press these to scroll along the digits.</p><p>Symbols on the displayThe time is shown if youve set the handsets clock The handsets number (1 if you have a single system, 1, 2 or 3 if you have a Twin or Triple system) The base units number (1, unless you have registered your handset to more than one base unit) The duration of each call is shown on the display from 20 seconds after you press the PHONE button for a line, until 5 seconds after you end the call.</p><p>What the symbols meanSignal level This shows the strength of the signal between the handset and base unit. It flashes while the handset is trying to establish a radio link to the base unit. If this symbol flashes while youre on a call, move closer to the base unit. This appears when you missed incoming calls (even if you do not use Caller Display). This flashes while your handset is ringing for an intercom call, and comes on steadily when the calls connected. This comes on when youre storing numbers in memory, and when youre making calls to stored numbers. This appears when the handset is dialling a non-local number via an alternative providers network. This appears when youre using Last Number Redial. This appears when youre checking, or dialling from, the list of Caller Display records. This appears when the keypad is locked, or when Call Barring has been turned on. When this shows nearly empty ( ), put the handset onto the base unit or charger pod as soon as possible, to charge the batteries. While the batteries are being charged, this symbol blinks.</p><p>New call</p><p>Intercom call Memory/ store Indirect network Redialling Caller Display Keypad locked Battery charge level</p><p>LNR/ CDS/ PAUSE button Press ONCE to make a repeat call to one of the last five numbers you dialled. Press TWICE to see a list of Caller Display records. Press to generate pauses when using the phone on a PBX. INT () button Press to make an intercom call.</p><p>Before you can use the handset to make calls you will need to fit and fully charge the batteries, as described on pages 4 and 5. Please read the notes on pages 2 and 3 before you install the base unit.</p><p>If the display is blank Press the button</p><p>to switch the handset on</p><p>ContentsRead these notes first 3 Caller Display 14</p><p>Choosing a site for the base unit and charger pod 3 Radio signals between handset and base unit 3 Mains power connection 3 Installation and set-up Before you start Electrical safety 6 Interference 6 Out of range warning 6 Switching on and off To switch the handset on and off 7 To lock the keypad 7 Making and answering calls To make a call 8 To answer a call 8 To end a call 8 Earpiece volume 8 Last Number Redial (LNR) 9 Memory dialling 10 8 7 4 6</p><p>To check Caller Display records 14 To return a call 15 To delete Caller Display records 15 To store a Caller Display number in memory 15 Using a multi-handset system To make an intercom call 16 To answer an intercom call 17 To end an intercom call 17 To transfer a call 17 To shuttle between two calls 18 To set up a three-way conference 18 New Call tone 19 To page all handsets from the base unit 19 To register a new handset to your base unit 20 To de-register a handset 21 To select a base unit 21 To register to a different brand of base unit 22 Customising your handset General points 23 Auto-answer 23 Ringer volume and melody 24 Key tone 24 Direct Call 25 To clear all memories 26 To reset the handset 26 Continued overleaf 23 16</p><p>To store a number 10 To make a memory call 10 Chain dialling 11 To change a stored number 11 To delete a stored number 11 To use the notebook 12 To store an LNR number in memory 13</p><p>Binatone Help Line: 01325 304 473</p><p>1</p><p>Contents</p><p>Read these notes firstCustomising your base unit 27 Guarantee and service 41 General points 27 Emergency numbers 27 Ringer volume and melody 28 Call barring 28 Date and time 30 To clear all Caller Display memories 31 To reset the base unit 31 Indirect Network 32 While the unit is under Guarantee 41 After the Guarantee has expired 41 Technical details 42</p><p>Choosing a site for the base unit and charger pod</p><p>The base unit and charger pod(s) should each be placed on a level surface, in a position where:I</p><p>I</p><p>I I I</p><p>To set the network access code 32 To set additional local dialling codes 33 To turn Indirect Network on and off 33 Troubleshooting Cleaning and care Declaration of conformity 34 40 40</p><p>the mains adapter plug will reach an easily accessible 230-V AC switched mains supply socket never try to lengthen the mains power cable the base units telephone cable will reach your telephone line socket or extension socket (the charger pod does not have a telephone line connection) it is not close to another telephone this can cause radio interference it is not close to a sink, bath or shower, or anywhere else where it might get wet it is not close to other electrical equipment fridges, washing machines, microwave ovens, fluorescent lights, TVs etc.</p><p>Radio signals between handset and base unit</p><p>Connection and conditions for useYou can connect your e3300 to a direct exchange line (DEL) a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. Do not connect the e3300 as an extension to a payphone. The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.) connected to an exchange line must not add up to more than 4 otherwise, one or more of them may not ring and/or answer calls correctly. The e3300 has a REN of 1, and most other telephones have a REN of 1 unless marked otherwise. Mains power connection</p><p>To use your handset and base unit together, you must be able to establish a radio link between them. Be aware that: I Any large metal object like a refrigerator, a mirror or a filing cabinet between the handset and the base unit may block the radio signal. I Other solid structures, like walls, may reduce the signal strength. IMPORTANT I The e3300 base unit must be used with mains</p><p>adapter, part no. XX002136D, supplied with the unit. I The e3300 charger pod must be used with mains adapter, part no. XX002137D, supplied with the unit. Using any other adapter will result in non-compliance with EN60950, and will invalidate any approval given to this apparatus.</p><p>2</p><p>Binatone Help Line: 01325 304 473</p><p>3</p><p>Installation and set-up</p><p>61Choose a suitable site for the base unit See page 3</p><p>Fit a battery pack in each handset A. Plug in the connector B. Tuck the wires in and lay the battery pack in the compartment C. Fit the battery compartment cover, sliding it into place and pressing firmly to make sure it is secure</p><p>2</p><p>Connect the mains power lead and the telephone line cord into the underside of the base unitRED BLACK</p><p>Use the telephone line cord supplied with your e3300 do not use any other telephone line cord</p><p>3</p><p>Plug the mains adapter into a 230 V AC, 50 Hz mains socket, with the switch on the socket set to OFFSee the note on page 3</p><p>7</p><p>Charge the batteries for 15 hours Before you use the handset for the first time, it is important to charge the batteries fully. The battery The handset beeps when its correctly level symbol blinks in position on the charging cradle. Leave the handset on the charging cradle for 15 hours.</p><p>4</p><p>If you have one or more charger pods Plug the mains adapter into a 230 V AC, 50 Hz mains socket, with the switch on the socket set to OFF</p><p>When you dont need to use the handset (for example, overnight or when you go out), replace it on the base unit or charger pod, to keep the batteries charged.</p><p>See the note on page 3</p><p>8 Connect the base unit to the telephone lineSwitch off power at the mains socket Insert the telephone line plug into the socket as shown Switch mains power back onMake sure the mains socket is switched on if you want to use the phone it will not work without electrical power</p><p>The Charge light comes on.</p><p>Use the plug to raise the shutter before pushing it into the socket</p><p>54</p><p>Switch on at the mains socket(s)</p><p>NOTE: the charger pod does not have a connection to the telephone line.</p><p>Binatone Help Line: 01325 304 473</p><p>5</p><p>Before you startElectrical safetyN</p><p>Switching on and offTo switch the handset on and off To switch the handset off and save battery power:</p><p>DO NOT let the base unit or charger pod get wet. Electrical equipment can cause serious injury if used while you are wet or standing in water. If the base unit (or the charger pod) ever falls into water, DO NOT retrieve it until you have unplugged the power lead from the mains and the telephone line plug from the telephone socket; then pull it out by the unplugged cables. NEVER use your e3300 outdoors during a thunderstorm unplug the base unit from the telephone line and the mains socket when there are storms in your area. Damage caused by lightning is not covered by the guarantee. If the sound quality gets worse as you move around while on a call, this is probably caused by interference between the handset and the base unit, perhaps because you are too near to another phone or other electrical equipment. Move to a different position to clear the interference. If you do not move, your call may be cut off.</p><p>N</p><p>Press the HANG UP/C button and hold it for 3 seconds until the display goes blank To switch the handset back on: Briefly press the HANG UP/C button</p><p>N</p><p>To lock the keypad</p><p>To lock the keypad:</p><p>Press the HANG UP/C button and hold it for 1 second until the key symbol and a group of dashes appear on the display To unlock the keypad:</p><p>Interference</p><p>Press the HANG UP/C button and hold it for 1 second until the key symbol disappears from the display Or simply replace the handset on the base unit or charger podI I</p><p>!Out of range warning</p><p>Radio interference in the environment may occasionally cause a short break in the link between the handset and the base unit while you are on a call. The handsets display will flash briefly, while the unit automatically restores the link. If you hear a warning tone during a call, and/or the sound in the earpiece becomes faint or distorted, you may be going out of range of the base unit. Move nearer to the base unit within 20 seconds, until the tone stops. Otherwise, your call may be cut off.</p><p>Notes</p><p>When the handset is switched off, it cant be used for making calls, including emergency calls. When the handset is switched off, it wont ring for incoming calls, but the base unit will still ring. To answer a call when the handset is switched off, you need to switch it back on. Remember that it may take a few moments for the handset to re-establish a radio link with the base unit.</p><p>6</p><p>Binatone Help Line: 01325 304 473</p><p>7</p><p>Making and answering calls</p><p>Making and answering callsTo make a call Last Number Redial (LNR) To make a repeat call to the last number you dialled (up to 24 digits):</p><p>1</p><p>Key in the telephone number If you make a mistake, press the HANG UP/C button to clear digits one by one from the display.</p><p>1 2</p><p>Press the LNR/CDS button Press the PHONE button To make a repeat call to one of the the last five numbers you dialled:</p><p>2</p><p>Press the PHONE button (You can dial the number after you press the PHONE button to get Dial tone if you prefer, but you wont be able to correct any mistakes if you do it this way.) If you want to use the Indirect Network feature, turn to page 32 for more information.</p><p>1 2 3</p><p>Press the LNR/CDS button Press the L or M button if necessary until the number you want is displayed Press the PHONE button To clear a number from the Last Number Redial (LNR) memories:</p><p>To answer a call</p><p>When theres an incoming call, call flashes on the display; and the base unit and handset ring (the handset rings softly at first, then gets louder).</p><p>To end a call</p><p>1</p><p>Press any button to answer the call Press the HANG UP/C button so that the PHONE light on the base unit goes out Or simply replace the handset on the base unit or charger pod During a call, to adjust the volume in the earpiece:</p><p>Press the LNR/CDS button, then the L or M button until the number you want to delete is displayed Press and hold the HANG UP/C button until you hear a tone; OR press and hold the HANG UP/C button for 5 seconds to clear all five LNR memoriesI</p><p>2</p><p>Earpiece volume</p><p>Notes</p><p>Press the L or M button There are three volume levels, shown by bars on the right-hand side of the display. After you end your call, the earpiece volume will stay at the level you have set.I I</p><p>Only numbers youve dialled manually will be stored in the LNR memories; not numbers youve dialled from memory or from the Caller Display list. Numbers you..</p>